Flash-Artemis- pomoc

[Bruca]

Ty jsi teda drson!! Napis co za certifikaci ti nefunguje. Jako kdybys mel zablokovany telefon od operatora. Ale to snad funguje jen na SIM kartu a ne na telefon doufam.

1. Vyjmi SIMku a SDkartu - Baterie musi byt nabita vice jak 50%
2: Pouzij Windows XP - Tvuj mobil musis videt jako pripojeny. Viz Activesync(XP) alias Mobile Center(vista)
3. Rozbal a spust :

Kód: Vybrat vše

http://rapidshare.com/files/301004578/00Shady_313_arte_uspl.rar.html
http://www.uloz.to/3591940/arte-uspl.rar

(na nazev nekoukej) Objevi se ti Cerne DOSove okno a po chvilce zacne pocitat do 100% musi to projit -- jeste se te parkrat zepta. Zaskrtnes okenko a das NEXT(dalsi) pokud ti pogratuluje mas odblokovany telefon pro novou ROM.
4. Stahni a spust :

Kód: Vybrat vše

http://rapidshare.com/files/301006657/HTC_P3300_WWE_3.13.405.1_4.1.13.44_02.94.90_Ship_R.exe.html

Automaticky spusti flashovani.
5. Pokud vyskoci varovna hlaska tak napis. Ale tohle na 90% funguje.

Zrovna nedavno jsem si skousel WM 6.5 .. vraceni na 6.1 uplne pohoda. Nekdy to musis skouset nekolikrat nez se to unlockne.

[ncf]

No díky,jenže já už toho vyzkoušel tolik,že fakt nevím, Nemohl by jsi mi prosím konkrétně pomoct?

[ncf]

No vždyť píšu,že mi to nejde propojit s Active Syncem...na telefonu jsou tři barevný pruhy-červená,zelůená,modrá a dole v bílý je vlevo na displeji nápis USB.. Active sync ho nevidí.. A když zkusím natvrdo tu ROMku,tak se zastaví na 3% a hodí hlášku Error happened (226)

[Bruca]

Odpojis kabel a znova pripojis. Musi se prihlasit.
Pokud ne uz mockrat se tu psalo ze je chyba v kabelu/konektoru nebo v systemu. Popripade spatne probehl proces HARD SPL.

Bez toho, aby te videl AS nemuzes absolutne nic nahrat. Dej Hard SPL znova opakuj obcas to pomuze.
Takze chyba neni v SOFTWARU kterym flashujes.

Malej vypis chybovych hlasek podle toho zjednas napravu.
(Nepodcenuj spojeni ActiveSync i v Bootloaderu je zarizeni viditelne!)
RUU = ROM Update Utility
A list of the Common RUU update errors and their common solutions / explanations.
Originally taken from this post by P1Tater at XDA Developers


ERROR [202, 204] : CONNECTION

This error message will appear when the device is not connected to ActiveSync correctly. Make sure you properly connect the device to the PC through ActiveSync before running RUU.
If the problem persists try removing and re-installing ActiveSync.


ERROR [206] : MEMORY ALLOCATION

When you see this error message, close other running programs on the computer and run RUU again.


ERROR [208] : FILE OPEN ERROR [210] : FILE READ

These error messages indicate that RUU lacks certain important files and cannot continue with the update. Please get the complete RUU package again.


ERROR [212] : FILE CREATE ERROR [214] : FILE WRITE ERROR [222, 224] : DEVICE NOT RESPONDING

These error messages will appear when remote access control has failed. Check the ActiveSync connection and try running RUU again.


ERROR [220] : MAIN BATTERY POWER

This error message will appear when the device's battery power is not sufficient. Although RUU will instruct you to plug in the AC adapter, it still has to make sure that your device has enough power to upgrade the radio. (Even when you plug in the AC adapter, the device is unable to charge the battery when it is upgrading the radio).


ERROR [226] : FILE WRITE

This could indicate that the downloaded image (.nbh file) is corrupt, re-download the image.


ERROR [238] : FILE READ

This error message may appear when, for some unknown reason, the ROM image on the Mobile Device is corrupt. Download the whole RUU and try again.


ERROR [240] : FILE OPEN

When this error message appears, check whether the downloaded image is placed in the directory of RUU. If, for some unknown reason, you find that the ROM image is not located in the RUU folder, you have to download the RUU and retry again. Check that the contents of the folder is a CustomRUU.exe file and an .nbh file. If you put the os-new.nb file in by mistake instead of the .nbh, this is the error that shows up. Thanks ConfusedSTU.


ERROR [242] : INVALID LANGUAGE ERROR [244] : INVALID MODEL ID

You're trying to flash an Image to a phone it wasn't designed to run on, i.e. a Kaiser Image on a Polaris.


ERROR [246] : DEVICE NOT RESPONDING

This error message indicates that RUU cannot start the update process. This usually indicates something is wrong with your device. If it continues happening after several attempts, try putting your phone into the bootloader before running the RUU. If you still cannot get it to work, please contact your service provider for assistance.


ERROR [248-259] : UPDATE ERROR

This error occurs when there is an "open port error" before upgrading the CE ROM image. You can soft reset the device and run RUU again. If you still encounter an "OPEN PORT ERROR" again, reset your computer and try again.


ERROR [260] : CONNECTION

This error occurs when the RUU cannot make a connection to the device right before flashing. This typically happens when you try to flash a new SPL to your device. Use Soft-SPL before attempting the RUU again.


ERROR [262] : UPDATE ERROR

This error occurs during the CE ROM code upgrade process. If this happens, you can just soft reset the device and run RUU again. The update process will then continue. At this stage the rom on the device is incomplete and it will not boot back up into Windows. You will need to place it into the bootloader to continue.


ERROR [280] : UPDATE ERROR

When you see any of these error messages, close other running programs on the computer and run RUU again.


ERROR [294] : INVALID VENDOR ID

You probably need to Install a HardSPL or CID Unlock your device.


ERROR [296] : UPGRADE ONLY

One of these error messages will appear when you use the wrong RUU to do the upgrade. RUU will check if the Model ID and Language ID are compatible with the device. Make sure you use the appropriate RUU tool to upgrade.


ERROR [300] : INVALID UPDATE TOOL

This error message will appear when you use the incorrect RUU version to upgrade.


ERROR [264, 274] : CONNECTION ERROR [302-318] : UPDATE ERROR ERROR [320-328] : INVALID COMMAND

These errors seldom occur. However, if one of these errors occurs, it usually is not recoverable and the device needs to be sent back to the customer service center. In this case, you have to flash a new ROM code. You can retry the RUU to see if it recovers.


ERROR [330] : ROM IMAGE ERROR

This error message will appear when you use the incorrect RUU to upgrade and the image file size is larger than the Flash ROM size. In this case, download the correct RUU version and make sure the image file is correct to upgrade.

[ncf]

zkouším normálně dát start USPL a vyjede DOS okno a nevidí zařízení.. AS mi to taky nepřipojí. Při ajkýmkoliv pokusu o nahrání ROM mi to hází 226...takže mám asi peška

[Bruca]

I to DOS okno je RUU takze pise chybovou hlasku. Staci precist.
DOS okno neni definitivni na jeho spodnim okraji to pocita do 100%

PS .. nevim jestli se pri HSPL odpoji AS je to mozne, ale ty musis pockat.

:idea: Samozrejme vse provadis na systemu XP. :idea:

[ncf]

Píše jen No device connected - a vyskočí další okno - would you like try copying again? yes-no-storno ,nikde nic nepočítá

[Bruca]

Takze klasicka chyba .. odinstaluj Active sync vcetne pouzivani jineho USB slotu.
Znova nainstaluj AS a opakuj.

Uz jsem mnohokrat psal ze staci obcas odpojit ... pockat ... a pak pripojit znova PDA. Pak se musi objevit zelene AS . A pokracujes YES. Dokud tohle neprekonas.
Hlavne nedavej NO a znova nespoustej. RUU pokazde resetuje USB pripojeni. Bohuzel se mi taky obcas stalo ze se PDA znova nepripojilo. Muj problem byl konektor nebo HW.

Skousej vse mozne, ale je to vina systemu XP nebo ActiveSync.
Take doufam ze pouzivas nejnovejsi AS od Mrkvacu!

Muzes skusit i primy Flash bez HARDSPL
Tohle jsou 3xoficialni Widows Mobile 5, ktere nepotrebuji HARD SPL Jedna z nich ti musi jit ostatni jsou pro jina zarizeni a tim ti i nepovoli Flash
Poskodila se mi WM6. Abych mohl nahrat o5 WM6 musel jsem downgradovat na WM5. Pak zas fungoval navod od bodu 1.

Kód: Vybrat vše

http://rapidshare.com/files/306069993/HTC_1.12.405.01_026790_WWE_SHIP-Faktory.rar.html
http://rapidshare.com/files/306100171/art_tmouk_11311001_024990_wwe_ship.exe.html
http://rapidshare.com/files/306100953/ARTE_DOPODAU_12570702_026990_WWE_SHIP.exe.html

Edit : Skus HardSPL jestli ani ten ... tak se systemem ti nikdo nepomuze. Musis najit nekoho s XP, ktery to skusi. Pak budes mit jistotu ze je neco s konektorem nebo HW.

[ncf]

Tak po reinstalu As na mý Xp se po připojení origo HTC kabelu objevila bublina v liště že zařízení Pocket PC je ninstalováno a připraveno k použití,ale As ho pořád nepřipojí..

[Bruca]

AS musi byt zeleny. Pak funguje Flash.